Hardware
FOXIT WEIGHBRIDGE SERIAL TO ETHERNET CONTROLLER
FOXWSEC is 8-port RS485 serial to Ethernet controller. It adopts Cortex-M7 solution which has a main frequency up to 400MHz, powerful performance, fast transmission speed, and high reliability. Equipped with a deeply optimized TCP/IP stack, bull in hardware and software watchdog and a variety of keepalive mechanisms, FOXWSEC keeps online all the time. It supports TCP Client, TCP Server, UDP Client, UDP Server and HTTPD Client working modes, achieves data transparent transmission via simple configuration.
New ARM core, CortexcM7 solution, equipped with deeply optimized TCPAP protocol stack, It has low latency and strong scalability, stable and reliable.
I supports Modbus TCP and Modbus RTU protocol mutual conversion, multi-host poling function.
The device conforms to industrial design standards. Reliable EMC protection and -40-85°C operating temperature make it endure various complex industrial scenarios.
Each serial port supports connecting to two different servers at the same time, Two sockets are mutually
backed up, providing higher reliability and better flexibility.
Features
- Supports 8 serial ports working independently.
- Supports 9-36V wide voltage input, with reverse polarity protection.
- Supports connecting to Virtual COM Port Driver (USR-VCOM).
- Supports static IP and DHCP client.
- Supports Modbus RTU to Modbus TCP protocol conversion.
- Multiple hardware protection, ESD level3(air-+8KV, contact-+4KV), Surge level3 (-+2KV), EFT level3 (-+2KV).
- Supports configuring parameters via built-in webpage.
- Supports upgrading firmware via built-in webpage and configuration software, more convenient.
- Supports hardware watchdog, automatically restarts when the device goes down.
- Supports WebSocket for bidirectional data transmission between a maximum of 16 WebSocket clients and any serial port
- Supports serial and network AT Commands.
- Supports UDP broadcast function.
For more details:
FOXWSEC is an 8-port RS485 serial to Ethernet controller featuring a Cortex-M7 solution with a main frequency up to 400MHz, ensuring powerful performance, fast transmission speeds, and high reliability. Its deeply optimized TCP/IP stack, along with built-in hardware and software watchdogs and various keepalive mechanisms, ensures continuous online presence.
Industrial RS485 Ethernet converters bridge the gap between RS485 serial devices and Ethernet networks. They enable reliable data transmission between industrial equipment and monitoring/control systems spread across larger distances. Here are the detailed specifications of an industrial RS485 Ethernet converter:
Input Specifications
- Input Voltage: DC 9.0-36.0V
- Input Current: 120mA@12V
Hardware Specifications
- Dimensions: 22212235mm (L”W”H, including terminals and mounting)
- Installation: Panel mounting
- Ground Screw: 1
- Operating Temperature: -40-85℃
- Storage Temperature: -40-105℃
- Operating Humidity: 5%-95% RH(non-condensing)
- Storage Humidity: 5%-95% RH(non-condensing)
- Certifications: CE/FCC/ROSH
Ethernet Port Specifications
- Ethernet Port Spec.: RJ45, 10/100Mbps, auto MDI/MDIX
- Ethernet Port No.: 1
Serial Signals Specifications
- Serial Signals: RS485: 3 lines (A+, B-, GND)
- Serial Port No.: 8 RS485
Interface Parameters
- Serial Baud Rate: 600-921.6k(bps)
- Data Bit: 7,8
- Parity: None, Even, Odd
- Flow Control: RS485: XON/XOFF
- RS-485 Pullup and Pulldown Resistor: 2.2ΚΩ
- ESD Level: IEC61000-4-2: Air:4KV, contact:4KV
- Surge Level: IEC61000-4-5: ±2KV level 3
- EFT Level: IEC61000-4-1: 12KV Level 3
Software Parameters
- Network Protocol: IP/TCP/UDP/ARP/ICMP/IPV4/DHCP/DNS
- IP Mode: Static IP, DHCP
- Modbus Gateway: Support
- Websocket: Support
- HTTP Chont: Support
- UDP Broadcast: Support
- User Configuring: Setup utility, webpage. AT commands
- Serial Packets Cache: Dynamic packet cache